It works with USB but again, not bluetooth. It's probably my fault for installing, and uninstalling all different kinds of drivers everywhere.Īnd do not use MotioninJoy. I don't understand how the SCP-DS-Driver-Package-1.2.2.175 worked with bluetooth while the new one doesn't. ![]() Trying the toolkit again and it looks like I have to reinstall Windows. I cannot gain access to my system32 folder to manually copy them anymore. Now the old software refuses to install the controller drivers. It didn't restart properly, it BSOD'd with the SCPVBUS error or something. I used that and everything was fine until I restarted my PC. This SCP Toolkit, doesn't work with bluetooth. What I'm trying to say, The SCP-DS-Driver-Package-1.2.2.175 was the only way to get them to work via Bluetooth. My controllers is fine as they work via USB and on a PS3 and PS4. The vibration works perfectly fine otherwise. Reply to this email directly or view it on GitHub I can connect via bluetooth using old scp When using old scpserver, I can get my controllers to vibrate on usb mode,īut not on bluetooth mode. Version doesnt work with bluetooth on these fake controllers? Version of motioninjoy and scpserver works with bluetooth, but ur latest Supplier told me its a genuine sony controller. Should I ask for a refund from the supplier? The 29, 2015 10:54 PM, "luzair" I have the same issue "FakeĬontroller detected". So, long story short: you should ask for a refund xDĮl dic. Who knows, maybe those fancyĬamouflage ones they sell are actually original, or they offer a dualshockĤ (I can dream hehe :P ) (seriously, I'll most likely get refunded) Instantly offered "a replacement or a refund". Original), mentioned that seemed to not be the case and I was almost If you want to know more about the inner workings of the Scp Bluetooth stack don't hesitate to not nefarius but you should. That's where the software is currently stuck. E se ainda não é inscrito clique no botão inscreva-se Acompanhe o canal. The PANHAIs just don't send the 3rd connection request for the HID Service channel which the originals do just fine. Se você gostou do vídeo, por favor deixe sua avaliação e comentário. What I've discovered so far is, that the actual pairing (sadly people misuse this term all the time the flashing LEDs do not necessarily indicate a pairing problem) works fine, it's the L2CAP connections which fail after responding to a connection and configuration request. The Logs the toolkit produces won't help much since the inner workings of the protocols involved aren't logged it would add too much of an overhead. I don't have much time either since I'd like to focus on development rather than reverse engineering. Since my knowledge of the whole Bluetooth specification (if I recall correctly, v4 has nearly a 1000 pages.) is very limited I wasn't yet able to decipher those dumps. I managed to tap into the communication between the Bluetooth controller chip and the micro controller (they communicate via UART thankfully) and actually could dump the streams they exchange when connecting to a genuine Sony PlayStation 3. I already installed microsoft drivers and installed 360 accessories.I got some different "breeds" of those PANHAIs donated a few month ago and had them disassembled. however when I do, my PC doesn't read my 360 controller. Additionally, the application also supports motion sensing and allows users to adjust the vibration settings. Went back, for the heck of it, tried the "plugged" option instead of XInput and still nothing.Ĭan anyone help me with this? Did I set up my DS4 wrong? Is there something else I can use other than N-RAGE? Is there a work-around to get N-RAGE using my DS4 properly? Please help. The program is universal for ScpToolkit PS3 and PS4. It wouldn't let me map out any buttons I selected use and booted up a game (Mario 64) and it still wouldn't read my DS4. But while using N-RAGE, it never detected my DS4. So then found this posts, downloaded N-RAGE 2.2.3c plugin and selected XInput. While mapping out the controls for P64, I used default Jabo 1.7.0.12 and was able to map out buttons on the DS4 so it was reading my controller except for (like mentioned in above posts) the C-Buttons where I always got "X Rotation -" when trying to map them to my right analog stick. ![]() I've been able to map out the buttons for emulators for NES, SNES, Sega, Gameboy etc and the DS4 works completely fine! But then of course I stumbled upon Project 64. What I did was use DS4 tool - Virtual Bus Driver - ScpDriver.exe - ScpServer.exe and that's how I got the controller to sync and work with USB port. It took me forever to figure out how to sync the DS4 controller to my PC but finally managed too. so had to re-open this thread and even create an account here hoping someone here would see and help.įirst of all, I'm a n00b to this whole scene. ![]() I've searched high and low for an answer and only found this thread.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |